You have probably polished your floor recently using Rejuvenate Floors Restorer and Polish. Soon after you have noticed that you floors are now covered in a waxy, hazy, or streaky coating.
Don’t freak out if you think Rejuvenate damaged your floors.
You don’t have to live with a murky situation forever. You may address this issue and restore the lovely appearance of your floors.
In this article we will explain why Rejuvenate sometimes leaves a film on floors and how to fix it for good.
Let’s dive in!
Why does a waxy film appear on your floor after using rejuvante?
Rejuvenate can sometimes leave behind a foggy residue on your flooring, which is a red flag.
Rejuvenate is actually made to accomplish the exact opposite, making your floors shining and brilliant.
So why does Rejuvenate occasionally leave a foggy film behind? Well several factors may explain this and the most common ones are the following:
• The floor floor material is incompatible with rejuvente
• You used too much product for your floor surface to clean
• Your floors were not cleaned properly
• You likely used steam mops
• Finally but not least your floors were not totally dry.
Our recommendation is to always follow the manufacturer’s instruction when cleaning your floors with rejuvenate.
Now that we have covered the most common reasons for the hazy film appearing after using rejuvenate, let’s see how to fix it.
How to remove rejuvenate: 9 easy steps
Step 1
Clean the area. Debris and dirt should be swept away because they will obstruct cleaning. To get rid of dust, vacuum.
Step 2
Pour 1 gallon of warm water and 1 cup of white vinegar into a bucket. Both wood and vinyl floors can be cleaned using the solution. The Rejuvenate’s compounds will be cut through by the acidic vinegar, which will also lift it off the surfaces.
Step 3
Dip the mop into the solution and wring out the extra. The wood floor panels can be harmed by using too much cleaning.
Step 4
From one end of the room to the other, sweep the flooring. Work along the planks’ direction. As you clean, dip the mop into the solution to rehydrate it. Keep going till the Rejuvenate has finished.
Step 5
In order to get rid of the Rejuvenate, try a floor stripper. Use one that is appropriate for the kind of flooring. Observe the directions on the packaging.
Step 6
Allow the floor to be penetrated by the stipper for 10 minutes. Use a nylon pad to scrub the floor.
Step 7
For large floors, rent a floor buffer from a home improvement retailer. Add a scrubbing pad to simplify the task.
Step 8
Clean the floor with a wet mop to get rid of any Rejuvenate residue. This will remove any residue you might have overlooked.
Step 9
Using a dry mop or cloths, rub the floor to dry.
3 Alternatives methods to remove rejuvenate on floors
1- Dish soap
Since it merely calls for common home items that you usually already have on hand, the soap and water technique of removing Rejuvenate is perhaps the simplest. A mop, a bucket, warm water, and a bottle of normal dish soap are all you need.
The procedures are simple:
Vacuum or sweep the floor thoroughly.
Two tablespoons of soap should be added to a gallon of warm water.
Apply pressure while you scour the area with your mop.
Mop the floor once again with simply water to rinse it.
Let the floor dry out.
Repeat until the floor looks as it did before.
If you’ve applied more than one coat of Rejuvenate to your floor, you might want to try another procedure because this one isn’t as successful on highly polished floors.
2- Windex Glass cleaner
Rejuvenate can be removed from your floors with Windex or any other glass cleaning solution.
For this technique, you’ll also need a mop, a bucket, and warm water in addition to the glass cleaner.
Once you have your supplies, take the following actions:
Clean the floors with care.
Spray your glass cleaner immediately on a 4 by 4 area.
Give the cleaner three to four minutes to sit.
Clean the space with a moist mop.
Allow the floor to fully dry.
Review the outcomes, and if necessary, repeat the procedure on all the floor’s troubled regions.
3- Ammonia
Ammonia is an inexpensive, efficient, and readily accessible cleaning chemical. It’s yet another efficient method for getting Rejuvenate off of floors.
Be aware that working with ammonia necessitates extreme caution before using this approach. It can be toxic if ingested or inhaled through the fumes. To avoid direct contact, never combine it with anything other than water, make sure the space is well-ventilated, and wear protective gear at all times.
If you have natural wood flooring, go with a different technique even if this strategy works well for tile, laminate, and vinyl floors. Ammonia is corrosive and has the ability to dull wood and ruin finishes.
This procedure calls for water, a mop, a bucket, gloves, and eye protection in addition to ammonia.
Following the assembly of your supplies, proceed with the following steps:
Sweep the floor utterly.
Put on protective eyewear and gloves to guard against ammonia irritants.
To ensure that there is enough airflow and ventilation in the space, open windows and doors.
For every gallon of water, mix one cup of ammonia.
Apply pressure while you scour the afflicted area thoroughly with your mop.
Mop the floor once again with simply water to rinse it.
Let the floor dry out.
To completely get rid of the residue, you might have to mop multiple times.
FAQs
How long does rejuvenate floor restorer last?
The application of Rejuvenate Floor Restorer can last 3 to 6 months, depending on floor traffic, after which point you can re-apply and continue to enjoy that spectacular finish and shine. Rejuvenate Floor Shine Refresher typically lasts 1-3 month
Is rejuvenate floor cleaner safe?
Floor Cleaner. Keep pets out of the area when applying. Rejuvenate products are non- toxic and non- hazardous once they dry. Our products are safe for people and pets
Wrapping Up
When you look down to see your lovely flooring entirely covered in an unsightly, hazy film, it’s simple to become alarmed. However, there’s no need to worry.
This issue is widespread and resolvable.
The primary offenders are:
using incorrect If you use too much rejuvenation merchandise
not fully washing the floor before applying it
not allowing it to totally dry on the flooring after applying it
Making use of a steam mop to clean the refinished surface
Start with the approach that Rejuvenate advises: scrubbing the floor with an alkaline-based floor stripper or cleaner like Zep if your floors are a mess after using Rejuvenate and you need a rapid way to remove the film left behind.
If that doesn’t work, try ammonia, Windex, or dish soap and water as an option.
Resources
[1] https://www.hunker.com/12412503/how-to-remove-rejuvenate
[2] https://prudentreviews.com/rejuvenate-ruined-floors/
[3] http://www.rejuvenateproducts.com/faq/floor-care-questions/how-long-will-rejuvenate-floor-restorers-last
[4] https://www.homedepot.com/p/Rejuvenate-32-oz-Floor-Cleaner-RJFC32RTU/202269999
